Which command is used to configure an IPv6 static default route?
Configuring an IPv6 static route is very similar to IPv4 except that the command is now ipv6 route. IPv6 enabled on at least one interface • An IPv6 address on that interface.
What is IPv6 default route?
• Default IPv6 Static Route – Similar to a quad zero IPv4 route, a default IPv6 static route is created by making the destination IPv6 prefix and prefix length all zeros,::/0. Step 1: Configure a directly connected IPv6 static route.
What is the IP address used in a default static route?
A default static route is simply a static route with 0.0. 0.0/0 as the destination IPv4 address. backup path to a primary static or dynamic route, in the event of a link failure. The floating static route is only used when the primary route is not available.
When an IPv6 static route is configured the next hop address can be?
Explanation: When a static route is configured with the next hop address (as in the case of the 192.168. 10.128 network), the output of the show ip route command lists the route as “via” a particular IP address.
How do I configure IPv6 routing?
enable IPv6 routing on a Cisco router using the ipv6 unicast-routing global configuration command. This command globally enables IPv6 and must be the first command executed on the router. configure the IPv6 global unicast address on an interface using the ipv6 address address/prefix-length [eui-64] command.
What is a characteristic of a floating static route?
Explanation: Floating static routes are static routes used to provide a backup path to a primary static or dynamic route, in the event of a link failure. They must be configured with a higher administrative distance than the original dynamic routing protocol has.
What is the difference between default route and default gateway?
A default route is a route entry in a routing table whereas a default gateway is a value, typically an IP address. When an IP packet is received by a router, it looks into the destination IP address in the packet.
How does default route work?
A default route is the route that takes effect when no other route is available for an IP destination address. If a packet is received on a routing device, the device first checks to see if the IP destination address is on one of the device’s local subnets.
What is the command for default route?
A default route configured by the “ip route” command is called the default static route. Some routing protocols such as RIP and EIGRP allow us to advertise the default static route.
What does IP route 0.0 0.0 0.0 0.0 mean?
In the Internet Protocol Version 4, the address 0.0. 0.0 is a non-routable meta-address used to designate an invalid, unknown or non-applicable target.
What is a standard static route?
Standard. The static route consists of a destination network address or host, a corresponding network mask, and the IP address of the next-hop IP address. Null (discard) The null route consists of the destination network address or host, a corresponding network mask, and either the reject or blackhole keyword.
How do I set a static route to default?
Configuring a default static route
- Enter global configuration mode. device# configure terminal.
- Enter 0.0. 0.0 0.0.
- (Optional) Enable the default network route for static route next-hop resolution. device(config)# ip route next-hop-enable–default.
- (Optional) Configure next-hop recursive lookup to resolve the next-hop gateway.
What is the correct syntax of a floating static route?
What is the correct syntax of a floating static route? Floating static routes are used as backup routes, often to routes learned from dynamic routing protocols. To be a floating static route, the configured route must have a higher administrative distance than the primary route.
What route would have the lowest administrative distance?
Answers Explanation & Hints:
The most believable route or the route with the lowest administrative distance is one that is directly connected to a router.
What command must be configured to enable the router to forward IPv6 packets?
Enable the router to forward IPv6 packets.
Enter the ipv6 unicast-routing global configuration command. This command must be configured to enable the router to forward IPv6 packets.